Want better mpg and lower avg EGT? TRY MACH 4s?!?!?!
#1
Registered User
Thread Starter
Join Date: Apr 2003
Location: Cummins Technical Center, IN
Posts: 6,564
Likes: 0
Received 6 Likes
on
5 Posts
Want better mpg and lower avg EGT? TRY MACH 4s?!?!?!
I can't believe it. There's simply no way a 150hp injectors can be easily street driven, right? They smoke like nuts, right?
Well, the most amazing thing with the Mach 4s over the DD2s is the smoke threshold. I could drive my DD2 smokelessly, but it took a little concentration.
With the Mach 4s, you can accelerate normally without worry about smoke! Granted, your "normal" will a little quicker after putting them in, but smokeless acceleration is easily achieved.
That said, they WILL smoke if you want! LOTS OF IT! Just mash it at too- low rpm and you can almost put the fire out.
These are JUST what I was looking for smoke-wise-- *I* control the smoke. The throttle is more sensitive (of course), but it's about the same as the 75hp injectors with an EZ set on most aggressive. I have NO other fueling mods at this point (sold the box).
So, I'm testing them with JUST the M4s, no box, no boost fooler, no nothing. Well, nothing besides my super-duper PowerCore BHAF
At steady cruise, EGT is about 50-100 degrees cooler. Get into the pedal, and they race higher-- very quickly. But I can still get up to 70mph before the temps hit 1400.
Some other notes:
-- boost is limited to the stock 21psi, so my results are based on that (WG is NOT blocked).
-- MPG was 20.5 based on a 130 mile hwy jaunt with LOTS of hot rodding and mostly WOT stuff. It appears these will net better mpg over then honed sticks. Same conditions with previous sticks got me about 18.5mpg.
-- Again, truck is setup with NO power chip or boost fooler at this point. (I'm between electronic bombs after selling the EZ and saving for/stewing on what's next)
-- My altitude here is 6000+ feet! Yes, they have fullY controllable smoke AT ALTITUDE.
-- Any hint of lag past 10psi or so is gone--- response is instantaneous. Lotsa fun on the hwy.
These sticks should take me as far as my HO pump will let me go. They should be the last set I ever buy!
Don M and Bob Wagner, thanks for being patient with me! Don, these are the best streetable sticks I have ever seen! LOVE THEM!
Justin
Well, the most amazing thing with the Mach 4s over the DD2s is the smoke threshold. I could drive my DD2 smokelessly, but it took a little concentration.
With the Mach 4s, you can accelerate normally without worry about smoke! Granted, your "normal" will a little quicker after putting them in, but smokeless acceleration is easily achieved.
That said, they WILL smoke if you want! LOTS OF IT! Just mash it at too- low rpm and you can almost put the fire out.
These are JUST what I was looking for smoke-wise-- *I* control the smoke. The throttle is more sensitive (of course), but it's about the same as the 75hp injectors with an EZ set on most aggressive. I have NO other fueling mods at this point (sold the box).
So, I'm testing them with JUST the M4s, no box, no boost fooler, no nothing. Well, nothing besides my super-duper PowerCore BHAF
At steady cruise, EGT is about 50-100 degrees cooler. Get into the pedal, and they race higher-- very quickly. But I can still get up to 70mph before the temps hit 1400.
Some other notes:
-- boost is limited to the stock 21psi, so my results are based on that (WG is NOT blocked).
-- MPG was 20.5 based on a 130 mile hwy jaunt with LOTS of hot rodding and mostly WOT stuff. It appears these will net better mpg over then honed sticks. Same conditions with previous sticks got me about 18.5mpg.
-- Again, truck is setup with NO power chip or boost fooler at this point. (I'm between electronic bombs after selling the EZ and saving for/stewing on what's next)
-- My altitude here is 6000+ feet! Yes, they have fullY controllable smoke AT ALTITUDE.
-- Any hint of lag past 10psi or so is gone--- response is instantaneous. Lotsa fun on the hwy.
These sticks should take me as far as my HO pump will let me go. They should be the last set I ever buy!
Don M and Bob Wagner, thanks for being patient with me! Don, these are the best streetable sticks I have ever seen! LOVE THEM!
Justin
#3
Registered User
Join Date: Mar 2004
Location: Iowa
Posts: 1,110
Likes: 0
Received 0 Likes
on
0 Posts
Now that my tranny is taken care of, I am thinking about Mach 4's to replace my current Mach 1.5's; but that also means a new turbo and so I have been trying to hold off, but it's tempting...
mishkaya
mishkaya
Trending Topics
#11
Registered User
Join Date: Mar 2004
Location: Phoenix
Posts: 61
Likes: 0
Received 0 Likes
on
0 Posts
Hey Hohn, next time you're getting on the freeway, roll onto it hard in 4th gear or 5th gear. I'm curious by how much you can out flow the wastegate ... With 120 sticks I was hitting 27psi w/o a fooler or elbow... Never even threw a code .
#12
DTR Advertiser
Originally posted by mcoleman
Hey Don, Have mine shipped yet? I'm having my extra head cleaned up this week so Floor It can get started on it also.
Hey Don, Have mine shipped yet? I'm having my extra head cleaned up this week so Floor It can get started on it also.
Mike,
Almost got them finished. The problem the entire time has been parts. I have been back ordered on them for months. Finally I received some parts and I have been working some serious hours to get them knocked out. I apologize for all the delays, but the demand has exceeded the supply and my ability to get them done in a timely fashion.
The first two months of this year we sold more 4, 5 and 6 size injectors than we sold in 18 months previously. A bad thing for speedy delivery and it stressed the small nozzle manufacturer we use to the max. The problem of parts supply is fixed now I cant run out of parts for at least a year.
Don~
#13
Registered User
Join Date: Apr 2003
Location: Backwoods of Missouri CSA
Posts: 1,346
Likes: 0
Received 0 Likes
on
0 Posts
Good, If I get the same results as Ray G. with the new hard parts I will be needing a a set of larger injectors for dyno and track use. I'll use the 4s for towing the horses.
#14
Registered User
Thread Starter
Join Date: Apr 2003
Location: Cummins Technical Center, IN
Posts: 6,564
Likes: 0
Received 6 Likes
on
5 Posts
Originally posted by azcrawler
Hey Hohn, next time you're getting on the freeway, roll onto it hard in 4th gear or 5th gear. I'm curious by how much you can out flow the wastegate ... With 120 sticks I was hitting 27psi w/o a fooler or elbow... Never even threw a code .
Hey Hohn, next time you're getting on the freeway, roll onto it hard in 4th gear or 5th gear. I'm curious by how much you can out flow the wastegate ... With 120 sticks I was hitting 27psi w/o a fooler or elbow... Never even threw a code .
I can get it to momentarily hit 25 just because of the GG hose I have somewhat restricts the WG signal.
When the gate opens, it comes down to 21-22psi and stays there!
jlh
#15
Registered User
Join Date: Oct 2003
Location: NewMarshfield,Ohio
Posts: 209
Likes: 0
Received 0 Likes
on
0 Posts
2.2 to 4's
Don if i change my current 2.2's to 4's what change would i notice in exhaust temps? Right now with box off towing 16,000pounds i can hit 1300 easily on hills.