y-knot

Well my favorite fellow showed up again today, this time he brung me my rancho traction bars. Don't get in a tussel, because to know Rancho doesn't offer a traction bar for our dodges. But, since I had a set on a chevy, and I new there length and mounting brackets, I ordered ones for it, and then just made the rear mount. Out trucks (2500 and 3500's) have a bigger spring with a larger spacing the the chevy 1500, so I just made a new rear mount and it bolted right on. Looks great, they are of coarse red powder coated, thats there company colors. Sets the truck off nice, I haven't driven it yet, I still have the front end off, and since that came today also, I'll be getting on it. It's ashame that Rancho don't make the traction bars for the Dodge, there is very little that they would have to do to make them fit. Oh well, guess they are missing out on a un-tapped market.

y-knot

Today I got to take the truck for a small test drive, and was very pleased. Everything worked great and together. The traction bars seem to move smoothly and work as addvertised. Of coarse you will remember these were bars for a late model chevy 1500 4x4, and I just made a rear mount for them. I'll get more miles on them and see what they do.

Got Smoke?

[quote author=y-knot link=board=7;threadid=21442;start=0#msg202126 date=1067279656]
Today I got to take the truck for a small test drive, and was very pleased. Everything worked great and together. The traction bars seem to move smoothly and work as addvertised. Of coarse you will remember these were bars for a late model chevy 1500 4x4, and I just made a rear mount for them. I'll get more miles on them and see what they do.
[/quote]

Am I the only one who thinks that these might be a little weak in design for all the torque of a Cummins? ???

Watched a guy bend some traction bars at Scheid this year, got it on tape! He got to about 260-270 feet and started hoping and one of the last couple of hop's before he clutched it they bent straight down!

y-knot

I don't think I will ever bend them. I had the same bars on a chev, and never bent them. the big ole cummins has alot of torque, but I have never snaped an axle, spit out a drive shaft, or twisted a motor mount in half? I have done all of this in other trucks? they are made of 1 1/2" x .188 wall Dom and are guseted on the ends. I have a set of FABRITECH bars on a pre-runner that might look beefier, but probally are not half as stout. I will post if one bends, deal?

Got Smoke?

[quote author=y-knot link=board=7;threadid=21442;start=0#msg202267 date=1067295921]
I don't think I will ever bend them. I had the same bars on a chev, and never bent them. the big ole cummins has alot of torque, but I have never snaped an axle, spit out a drive shaft, or twisted a motor mount in half? I have done all of this in other trucks? they are made of 1 1/2" x .188 wall Dom and are guseted on the ends. I have a set of FABRITECH bars on a pre-runner that might look beefier, but probally are not half as stout. I will post if one bends, deal?
[/quote]

Deal. How about snap'n some pics of the setup?

y-knot

Sure I have taken some, and I am having them put on a disk. But, I will need help getting them from my disk, to this site. Any one with some info that might help, please post in. Thanks

dodgeram

which year of chevy were the bars for ........... I can get the welder at work to fab up some rear mounts if I know wich ones to order ............

thanks

y-knot

The RANCHO part numbers are 1.) mounts RS5577
2.) bars RS6672
I ordered these thru Off Road Wherehouse (ask for Sonny)
1-800-341-7757

Got Smoke?

[quote author=y-knot link=board=7;threadid=21442;start=0#msg202608 date=1067365869]
The RANCHO part numbers are 1.) mounts RS5577
2.) bars RS6672
I ordered these thru Off Road Wherehouse (ask for Sonny)
1-800-341-7757
[/quote]

Y-knot you have a PM.