best place to buy 4inch exhaust ..cheap...
11-24-2008, 12:47 PM
#18
Registered User
Join Date: Aug 2006
Location: Fort McMurray, Alberta
Posts: 5,426
Likes: 0
Received 0 Likes
on
0 Posts
it went both directions, even put a hole in the torque tube on the intake... it has some serious carnage,, one of these days I am going to take some pics and post them... it is a mess for sure.. I am going to pull the intercooler off this week and see if there is any damage in ther too
11-25-2008, 08:27 PM
#19
Registered User
Join Date: Mar 2008
Location: grande prarrie
Posts: 346
Likes: 0
Received 0 Likes
on
0 Posts
I'v been told you can weld stanless with a regular mig useing wire ment for steel, but it will rust cus its regular steel in the weld and prbably not as strong as using the proper wire for stainless.
I would try the afe exhuast its pretty cheap, cost around the same as mbrp aluminized but its stainless. IT'll still rust, but i think it'll take longer to rust a hole though than the aluminized. NADP was selling it, probably still are. I've done a few they fit pretty good, not as good as MBRP though
I would try the afe exhuast its pretty cheap, cost around the same as mbrp aluminized but its stainless. IT'll still rust, but i think it'll take longer to rust a hole though than the aluminized. NADP was selling it, probably still are. I've done a few they fit pretty good, not as good as MBRP though
11-27-2008, 10:43 PM
#22
Registered User
Join Date: Oct 2006
Location: Okotoks AB
Posts: 3,142
Likes: 0
Received 0 Likes
on
0 Posts
Does it look something like this?
i fished that turbine wheel out fron the base of the stack, after it when through the resonator/ and down the s-pipe down tube.
AND.........the compressor wheel spun just fine on the other side of this. didn't damage the blades at all.........
i fished that turbine wheel out fron the base of the stack, after it when through the resonator/ and down the s-pipe down tube.
AND.........the compressor wheel spun just fine on the other side of this. didn't damage the blades at all.........
11-28-2008, 12:01 AM
#25
Registered User
Join Date: Oct 2006
Location: Okotoks AB
Posts: 3,142
Likes: 0
Received 0 Likes
on
0 Posts
just a turbo failure under load. yup its a big garrett. actually the fish mouths go all the way down looked just like a candy striper pole red & white round & round.
11-28-2008, 09:56 AM
#26
The Guru
Join Date: Jan 2004
Location: Airdrie Canada
Posts: 6,589
Likes: 0
Received 0 Likes
on
0 Posts
How did it break? Compressor surge and/or overspeed? I can't see the pictures but thats what usually kill things. How dirty is the filter? Another turbo killer.
12-06-2008, 09:21 AM
#28
The Guru
Join Date: Jan 2004
Location: Airdrie Canada
Posts: 6,589
Likes: 0
Received 0 Likes
on
0 Posts
Luke, you have anymore pics? Are the turbine blade tips scored? How heavy? That shaft looks nasty badly twisted piece, I wonder if the compressor was surge and turbine blades were smashed turbine housing going at around 100k cpm. Any compressor pics?
Thread
Thread Starter
Forum
Replies
Last Post
5.9Excursion
3rd Gen Engine and Drivetrain -> 2003-2007
10
11-21-2007 06:50 PM
tywebb3
Performance and Accessories 2nd gen only
2
12-30-2006 09:39 PM
Lambo
Performance and Accessories 2nd gen only
5
05-25-2004 06:27 PM
Chris_O
Performance and Accessories 2nd gen only
30
09-19-2003 06:51 AM