stupid question- how do I get the headlight bulbs out?.
#1
Registered User
Thread Starter
stupid question- how do I get the headlight bulbs out?.
yeah i'm serious How hard is it to change the headlight bulbs in my 05. I took a quick look out in the cold today and everything is in the way behind them?? Whats the deal?? how many things have to come out? I’m old school- I’m used to removing 4 phillips headed screws from the front. LOL
#2
Registered User
Join Date: Mar 2006
Location: Victoria,TX
Posts: 424
Likes: 0
Received 0 Likes
on
0 Posts
Well now that I say this it will happen!!! This is the one thing I havent had to do yet. I looked in the service manual and here is what is says. For some reason I couldnt get the pics to come with it! Hope this helps!!
LAMP
1. Disconnect and isolate the battery negative cable.
2. Disengage the three plastic retainers (3) that
secure the rubber welt (2) on the inboard side of
the front lamp unit (5) to the fender ledge.
3. Remove the three screws (4) that secure the front
lamp unit to the fender.
4. Pull the lamp away from the fender far enough to
access the wire harness connections (1) on the
back of the lamp housing.
5. Disconnect the headlamp wire harness connector
(4) from the headlamp bulb socket (5).
6. Disconnect the park and turn signal lamp wire harness
connector (3) from the park and turn signal
bulb socket (2).
7. Remove the front lamp unit from the fender.
LAMP
1. Disconnect and isolate the battery negative cable.
2. Disengage the three plastic retainers (3) that
secure the rubber welt (2) on the inboard side of
the front lamp unit (5) to the fender ledge.
3. Remove the three screws (4) that secure the front
lamp unit to the fender.
4. Pull the lamp away from the fender far enough to
access the wire harness connections (1) on the
back of the lamp housing.
5. Disconnect the headlamp wire harness connector
(4) from the headlamp bulb socket (5).
6. Disconnect the park and turn signal lamp wire harness
connector (3) from the park and turn signal
bulb socket (2).
7. Remove the front lamp unit from the fender.
#4
Registered User
Join Date: Apr 2004
Location: Sturgis SD
Posts: 1,609
Likes: 0
Received 0 Likes
on
0 Posts
Yep what runamuk said. Just pull the whole assembly out. It takes a pretty good pull go get it out but it will come. Also be careful of the paint on the bumber when you pull it, i scrached mine up a little when I pulled mine. Joel
#5
Registered User
Thread Starter
so your saying that thing is just pushed into some grommets or something? heck, I'll have to install 4 phillips head screws to feel safe!! thanx.
#6
Registered User
Join Date: Jan 2007
Location: Wisconsin
Posts: 504
Likes: 0
Received 0 Likes
on
0 Posts
Trending Topics
#8
Registered User
Join Date: Aug 2006
Location: Fort McMurray, Alberta
Posts: 5,426
Likes: 0
Received 0 Likes
on
0 Posts
there are 3 bolts,, 2 on the inside, and 1 between the bumper and the headlight on the outside of the light, the grommet is also back there. The hardest part is getting a torx long enough to take out the bottom 1, I went and bought a little ratched and extension and torx and leave it in my consel just in case
kevin
kevin
#9
Registered User
Join Date: Mar 2006
Location: Victoria,TX
Posts: 424
Likes: 0
Received 0 Likes
on
0 Posts
Well I have a post out there asking the same sort of question. In a nut shell do you know where to go to get the service manual like the shop techs have? that is what I have on my comp for the 05 models but I was wanting it for the 07
#10
Registered User
Thread Starter
#12
#13
Registered User
Thread Starter
well I installed the DOT approved blue bulb-whatever they are . -----------------------and I don't like em. I'm going to look into some super whites.thanx,crossy
#14