Smoke Switch for TST
07-19-2007, 07:40 PM
#1
Registered User
Thread Starter
Join Date: Apr 2004
Location: Sturgis SD
Posts: 1,609
Likes: 0
Received 0 Likes
on
0 Posts
Smoke Switch for TST
Would any of you guys that did the quad smoke switch look and see what wires on the motor side of the map senser you taped into. Which wire on the motor map plug does the dark blue wire on the quad plug into and the same for the red wire. I bet thats about as clear as mud but I hope someone understands, I want to try this with my TST. Thanks Joel
07-19-2007, 08:19 PM
#4
Registered User
Join Date: Feb 2007
Posts: 1,126
Likes: 0
Received 0 Likes
on
0 Posts
A "smoke switch" is a toggle switch that you put in the cab. When you flip the switch, the MAP sensor reads full boost and the chip gives max fueling to put out a lot more smoke. It's something you can do at an intersection or whenever you want to smoke someone out. You can't drive around with it on and it doesn't come with the chip. Only use it for short periods of time (5-10 seconds) and you have to make it up..... That's what I've heard anyways.....
07-19-2007, 08:28 PM
#5
Registered User
Join Date: Jun 2007
Location: NorCal
Posts: 941
Likes: 0
Received 0 Likes
on
0 Posts
A "smoke switch" is a toggle switch that you put in the cab. When you flip the switch, the MAP sensor reads full boost and the chip gives max fueling to put out a LOT of smoke. It's something you can do at an intersection or whenever you want to smoke someone out. You can't drive around with it on and it doesn't come with the chip. Only use it for short periods of time (5-10 seconds) and you have to make it up..... That's what I've heard anyways.....
07-19-2007, 08:35 PM
#6
Registered User
Join Date: Jun 2007
Location: NorCal
Posts: 941
Likes: 0
Received 0 Likes
on
0 Posts
Would any of you guys that did the quad smoke switch look and see what wires on the motor side of the map senser you taped into. Which wire on the motor map plug does the dark blue wire on the quad plug into and the same for the red wire. I bet thats about as clear as mud but I hope someone understands, I want to try this with my TST. Thanks Joel
Trending Topics
07-19-2007, 09:14 PM
#10
Registered User
Join Date: Jun 2007
Location: NorCal
Posts: 941
Likes: 0
Received 0 Likes
on
0 Posts
I would say that with the key on, you should be able to find the 5vdc wire.'
According to my Commander install instructions the wire on the map sensor is pin "D", or the blue wire on the far right side of the plug. Put the toggle switch between the 5vdc wire and the pin"D" wire. Again this is all just guessing, hopefully someone might chime in and give some other imput.
According to my Commander install instructions the wire on the map sensor is pin "D", or the blue wire on the far right side of the plug. Put the toggle switch between the 5vdc wire and the pin"D" wire. Again this is all just guessing, hopefully someone might chime in and give some other imput.
07-19-2007, 10:15 PM
#12
Banned
Join Date: Dec 1969
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
its these kind of mods that have the EPA and Green Peace breathing down our necks. good jobs guys killing mother nature. very immature...
haha so if any of you know me, then you know im completly full of crap. whos done the right up? i want one!! the smarty puts out enough smoke, but sometimes you need a little extra!
brett
haha so if any of you know me, then you know im completly full of crap. whos done the right up? i want one!! the smarty puts out enough smoke, but sometimes you need a little extra!
brett
