MP-8 & Edge w/Attitude - hot-unlock
#1
Registered User
Thread Starter
Join Date: Nov 2006
Location: Texas
Posts: 749
Likes: 0
Received 0 Likes
on
0 Posts
MP-8 & Edge w/Attitude - hot-unlock
How well do these stack together? Are there any settings I need to look out for on either unit for them to work better together?
#2
Administrator/Jarhead
Yes, they work great together!
Watch your EGT's, that's a big thing. The edge runs really hot.
Watch your rail pressure.
I do not know if the edge on the 06's adds timing, so listen for timing knock.
My MP-8 stack with the edge was great...
Watch your EGT's, that's a big thing. The edge runs really hot.
Watch your rail pressure.
I do not know if the edge on the 06's adds timing, so listen for timing knock.
My MP-8 stack with the edge was great...
#5
They will work. Now with what you are doing with it you most likely will be able to drain the fuel rail on an all out hard pull. A modified injection pump and a high flow lift pump will help you there. You would definitely need to have the better lift pump. I don't see a turbo upgrade in your signature. Without a turbo you will melt that motor into itty bitty pieces. Definitely need more air.
#6
Registered User
Thread Starter
Join Date: Nov 2006
Location: Texas
Posts: 749
Likes: 0
Received 0 Likes
on
0 Posts
They will work. Now with what you are doing with it you most likely will be able to drain the fuel rail on an all out hard pull. A modified injection pump and a high flow lift pump will help you there. You would definitely need to have the better lift pump. I don't see a turbo upgrade in your signature. Without a turbo you will melt that motor into itty bitty pieces. Definitely need more air.
Here are what my mods will be when I'm done (by Jan.)
HTT 64/65/13SS
ATS Exhaust Manifold
PureFlow Air Dog 150
TS Performance MP-8
F1 Flux 1/40HP Injectors
S&B Cold Air Intake
Edge Juice w/Attitude - Hot Unlock
Donaldson Muffler / No CAT
Goerend Torque Converter
Goerend Valve Body
DTT Flex Plate
Sonnax 1 Piece Billet Input Shaft
Mag-Hytec Trans. Pan
#7
Registered User
Here are what my mods will be when I'm done (by Jan.)
HTT 64/65/13SS
ATS Exhaust Manifold
PureFlow Air Dog 150
TS Performance MP-8
F1 Flux 1/40HP Injectors
S&B Cold Air Intake
Edge Juice w/Attitude - Hot Unlock
Donaldson Muffler / No CAT
Goerend Torque Converter
Goerend Valve Body
DTT Flex Plate
Sonnax 1 Piece Billet Input Shaft
Mag-Hytec Trans. Pan
HTT 64/65/13SS
ATS Exhaust Manifold
PureFlow Air Dog 150
TS Performance MP-8
F1 Flux 1/40HP Injectors
S&B Cold Air Intake
Edge Juice w/Attitude - Hot Unlock
Donaldson Muffler / No CAT
Goerend Torque Converter
Goerend Valve Body
DTT Flex Plate
Sonnax 1 Piece Billet Input Shaft
Mag-Hytec Trans. Pan
Trending Topics
#8
Administrator/Jarhead
I will also agree with what Pat said, the Edge made my rail pressure go down bad... 12k at WOT I think. I had the arson II CP3 mod at the time, and it did not help. (works wonders with the smarty...)
Ya may want to invest in a rail pressure guage. I have a quadzilla, and mine has been trouble free, but other people hate them due to constant problems.
Here is a vid of my edge on lvl6 with all my crap turned up. RP was poo...
#9
Here are what my mods will be when I'm done (by Jan.)
HTT 64/65/13SS
ATS Exhaust Manifold
PureFlow Air Dog 150
TS Performance MP-8
F1 Flux 1/40HP Injectors
S&B Cold Air Intake
Edge Juice w/Attitude - Hot Unlock
Donaldson Muffler / No CAT
Goerend Torque Converter
Goerend Valve Body
DTT Flex Plate
Sonnax 1 Piece Billet Input Shaft
Mag-Hytec Trans. Pan
HTT 64/65/13SS
ATS Exhaust Manifold
PureFlow Air Dog 150
TS Performance MP-8
F1 Flux 1/40HP Injectors
S&B Cold Air Intake
Edge Juice w/Attitude - Hot Unlock
Donaldson Muffler / No CAT
Goerend Torque Converter
Goerend Valve Body
DTT Flex Plate
Sonnax 1 Piece Billet Input Shaft
Mag-Hytec Trans. Pan
#10
Registered User
Thread Starter
Join Date: Nov 2006
Location: Texas
Posts: 749
Likes: 0
Received 0 Likes
on
0 Posts
Some good parts in there definitely. I still don't see anything either with a modded CP3 pump or a twin CP3 kit. You really are going to want to address something there. Otherwise you will be hard on it and it will start to pop and fart because there just isn't any fuel in the rail. You can run a good scanner on it and have it show your desired vs actual rail pressure. You want to have the two numbers within 4000psi of each other.
#11
If you were just running the Edge box with the injector, you would probably be ok. But you are throwing the MP8 into the mix which is just a pressure box. With all three there wont be enough fuel in the rail. Take either the injectors or the MP8 out of the equation, you should be ok.
#12
Registered User
Join Date: Jun 2007
Location: Alaska
Posts: 341
Likes: 0
Received 0 Likes
on
0 Posts
I'd also suggest going with a 62/71/13 instead of the 64/65/13. It will save you alot of surging, and will give you plenty of air for the fueling mods you have listed.
#13
Registered User
TNT and mp8 does not surge a 64/65/13. Will throwing the injectors in the mix - I don't know, but that 64 is a pretty impressive turbo.
#14
Registered User
Thread Starter
Join Date: Nov 2006
Location: Texas
Posts: 749
Likes: 0
Received 0 Likes
on
0 Posts
If you were just running the Edge box with the injector, you would probably be ok. But you are throwing the MP8 into the mix which is just a pressure box. With all three there wont be enough fuel in the rail. Take either the injectors or the MP8 out of the equation, you should be ok.