Just welded up the Donaldson M085171...
#1
Registered User
Thread Starter
Join Date: Mar 2006
Location: Hobart, IN
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Just welded up the Donaldson M085171...
Went pretty well for my boy & I.
Took our time, made a few measurements and started cutting with the torch, then welded it up and listened to the mellow tone.
Took it out and got up to about 50MPH, idleding at stops it sounds real good...EGT's look to be 30degs cooler....
Also did a home made PSM style intake, the EAA189 will be here shortly.
Some more here
Took our time, made a few measurements and started cutting with the torch, then welded it up and listened to the mellow tone.
Took it out and got up to about 50MPH, idleding at stops it sounds real good...EGT's look to be 30degs cooler....
Also did a home made PSM style intake, the EAA189 will be here shortly.
Some more here
#6
Registered User
Thread Starter
Join Date: Mar 2006
Location: Hobart, IN
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the site compliment trik396, yeah the bushys' a lot o fun.
A couple of questions; What kind of wire did you use in the mig?
.023, dialed in and practiced on a old flowmaster and tail pipe in the junk heap....basically a lot of spot welds, fill in the blanks then...
And did you have to put in any elbows?
No elbows, and it barely changed the angle on the tail pipe. thats why I went with the 41"er, figured it would allow a little wiggle room.
Yes, the pipes allow some play to line it out once in place.
A couple of questions; What kind of wire did you use in the mig?
.023, dialed in and practiced on a old flowmaster and tail pipe in the junk heap....basically a lot of spot welds, fill in the blanks then...
And did you have to put in any elbows?
No elbows, and it barely changed the angle on the tail pipe. thats why I went with the 41"er, figured it would allow a little wiggle room.
Yes, the pipes allow some play to line it out once in place.
#7
Registered User
Join Date: Dec 2004
Location: Arizona
Posts: 77
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the site compliment trik396, yeah the bushys' a lot o fun.
A couple of questions; What kind of wire did you use in the mig?
.023, dialed in and practiced on a old flowmaster and tail pipe in the junk heap....basically a lot of spot welds, fill in the blanks then...
And did you have to put in any elbows?
No elbows, and it barely changed the angle on the tail pipe. thats why I went with the 41"er, figured it would allow a little wiggle room.
Yes, the pipes allow some play to line it out once in place.
A couple of questions; What kind of wire did you use in the mig?
.023, dialed in and practiced on a old flowmaster and tail pipe in the junk heap....basically a lot of spot welds, fill in the blanks then...
And did you have to put in any elbows?
No elbows, and it barely changed the angle on the tail pipe. thats why I went with the 41"er, figured it would allow a little wiggle room.
Yes, the pipes allow some play to line it out once in place.
Trending Topics
#8
Registered User
Join Date: Sep 2003
Location: Southern Utah
Posts: 910
Likes: 0
Received 0 Likes
on
0 Posts
I have the same Donaldson. Great muffler, I've been running it since 2003. It is straight thru, not off-set. Because of this, the tailpipe will sit in further and without a extention it will start to turn the bumper black with soot. I added a chrome tip to put the tailpipe back out where it belongs, and all is good now.
#9
Registered User
Thread Starter
Join Date: Mar 2006
Location: Hobart, IN
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Galvanic corrosion?, you gotta have allot of fluid (water) contact in common with both metals.
If I can get a magnet to stick on the metals, I know I can weld it...tail pipe liked the magnet
#11
Registered User
Join Date: Dec 2004
Location: Arizona
Posts: 77
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the welding lesson. My usual plan is if I can get a ground clamp on it I can try to weld it, then grind it off, then put some bondo on it, then paint it.
#12
Registered User
Join Date: Apr 2004
Location: Edmonds WA
Posts: 532
Likes: 0
Received 0 Likes
on
0 Posts