12 Valve Engine and Drivetrain Talk about the 12V engine and drivetrain here. This is for 1994-1998.5 engine and drivetrain discussion only.

Computer code

Thread Tools
 
Search this Thread
 
Old 08-21-2006 | 12:58 PM
  #1  
Greguw's Avatar
Thread Starter
Registered User
 
Joined: Oct 2005
Posts: 326
Likes: 0
From: Pennslyvania , Lower Bucks County
Computer code

I have a computer code from a snap scanner Po118 ect ...is the coolant sensor...?

Thanks

Greg
Old 08-21-2006 | 01:05 PM
  #2  
JD730's Avatar
Registered User
 
Joined: May 2005
Posts: 2,510
Likes: 1
From: Belvidere, NJ
Yup,
P0118-ENGINE COOLANT TEMPERATURE (ECT) SENSOR
VOLTAGE TOO HIGH
Old 08-21-2006 | 01:09 PM
  #3  
Greguw's Avatar
Thread Starter
Registered User
 
Joined: Oct 2005
Posts: 326
Likes: 0
From: Pennslyvania , Lower Bucks County
My tranny was acting weard ... not shifting ... I stopped at my trany guy and the computer was not telling the trany to shift and that was the code that was in the computer ...we tried to clear it it would not .
So I guess I will have to fork out some dough ...LOL

Thanks

Greg
Old 08-21-2006 | 01:37 PM
  #4  
JD730's Avatar
Registered User
 
Joined: May 2005
Posts: 2,510
Likes: 1
From: Belvidere, NJ
Greg,
I'm not sure being I run mostly 1st gens and I haven't had problems with the 96 yet, but I think the coolant temp is used by the computer to decide wether or not to shift the trans into overdrive. I'm not sure about the rest of the gears.
Old 08-21-2006 | 02:34 PM
  #5  
Greguw's Avatar
Thread Starter
Registered User
 
Joined: Oct 2005
Posts: 326
Likes: 0
From: Pennslyvania , Lower Bucks County
I hate to throw parts in and waste money ... earllyer in the week my temp gauge was reading really low inside the truck ...I wiggled the connector and it started to read on the gauge .
The Tranny was done 6 months ago and the tranny was fine up until a few weeks ago it started to act up ...popping in and out of gears ...losing clutch pressure and eratic shifts ...some times it's fine .
The end of the coolant send dose wiggle ...I'm not sure by design ...the new one is a Standard motor ...my cost 80 bucks ...it listed for 150 ...not cheap.
We ran it on the scanner and the scanner was not sending any signals to shift when it should have been .
The code came up and would not allow it to be cleared from the computer ... I'm going to install the sender ...it is in a real pain in the butt place ...LOL

Thanks


Greg
Old 08-22-2006 | 05:39 AM
  #6  
Greguw's Avatar
Thread Starter
Registered User
 
Joined: Oct 2005
Posts: 326
Likes: 0
From: Pennslyvania , Lower Bucks County
The truck seems to be shifting and preforming fine ...I would say yes the Coolant sensor plays a big part in controling the computer .

Thanks

Greg
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
gerdes15
3rd Gen Engine and Drivetrain -> 2003-2007
4
02-25-2008 03:26 PM
boomer
1st Gen. Ram - All Topics
9
11-28-2005 07:58 PM
CAHunter
2nd Gen. Dodge Ram - No Drivetrain
1
09-09-2005 09:43 AM
shortround
2nd Gen. Dodge Ram - No Drivetrain
4
12-20-2003 05:07 PM



Quick Reply: Computer code



All times are GMT -5. The time now is 12:23 PM.